Pay in installments of $27.75 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Aug 22 - Aug 27
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
SpeedyBee F405 Mini Stack - F405 V3 FC + 35A 3-6S BLHeli_S 4-in-1 ESC - 20x20The SpeedyBee F405 Mini BLS 35A 2020 Stack features an upgraded F405 flight controller chip and a built in Bluetooth chip for seamless wireless Betaflight tuning. This board comes with a 4 level battery voltage display and a built in barometer and supports connectivity to all DJI Air Units. It offers 4 available UART ports, and a dual BEC setup with 5V 2A and 9V 3A outputs. The 35A 4 in 1 BLHeli_S Mini ESC provides four synchronized outputs with a
The SpeedyBee F405 Mini BLS 35A 20×20 Stack features an upgraded F405 flight controller chip and a built-in Bluetooth chip for seamless wireless Betaflight tuning. This board comes with a 4-level battery voltage display and a built-in barometer and supports connectivity to all DJI Air Units. It offers 4 available UART ports, and a dual BEC setup with 5V 2A and 9V 3A outputs.
The 35A 4-in-1 BLHeli_S Mini ESC provides four synchronized outputs with a continuous current of 35A, delivering strong power to drive all 2-4 inch and lightweight 5-inch quadcopters via a 4-6S battery. Equipped with a TVS transient suppression diode onboard, it better absorbs surge voltage, providing enhanced protection for the ESC.
Features
- TVS transient suppression diode for surge voltage absorption and enhanced protection
- Compatibility with 2-4 inch and lightweight 5-inch quadcopters
- Four synchronized outputs with a continuous current of 35A
- Dual BEC setup: 5V 2A output and 9V 3A output
- Built-in Bluetooth chip for wireless Betaflight tuning
- Supports connectivity to all DJI Air Units
- Upgraded F405 flight controller chip
- 4-level battery voltage display
- 35A continuous current output
- Supports 4-6S battery
- 4 available UART ports
- Built-in barometer
Specifications
SPEEDYBEE F405 V3 20X20 FLIGHT CONTROLLER
- DJI Air Unit Compatibility: Compatible with all DJI Air Units (DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1). Use specific solder pads for pin-to-pin connection. Note: UART1 is used for OSD and SUBS(R2) is used for SBUS receiver signal input
- BLE Bluetooth: Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Note: MSP switch on UART 4 must be turned on and set to a baud rate of 115200 for Bluetooth functionality
- Wireless FC Firmware Flashing: NOT Supported. Connect to Betaflight configurator on PC for firmware update
- Wireless Blackbox Download & Analysis: NOT Supported. Connect to Betaflight configurator on PC for blackbox analysis
- Current Sensor Input: Supported. For SpeedyBee BLS 35A V2 ESC, set Scale=250 and Offset=-500
- Power Input: 3-6S LiPo. Powered through 8pin harness G, V wires or G, V pads from bottom side
- BOOT Button: Supported. Forces FC to enter DFU mode for firmware flashing
- 3.3V Output: Supported. Designed for 3.3V input receivers. Up to 500mA current load
- 4.5V Output: Supported. Designed for radio receiver and GPS module. Up to 1A current load
- Mounting: 20 x 20mm, 3.5mm hole diameter. Compatible with M2 and M3 screws/Silicone grommets
- I2C: Supported. DA & CL pads on the front side for magnetometer, sonar, etc
- Traditional Betaflight LED Pad: Supported. Used for WS2812 LEDs
- Supported Flight Controller Firmware: BetaFlight (Default), INAV
- BetaFlight Camera Control Pad: Yes. CC pad on the front side
- ESC Signal: M1 - M4 wires or soldering pads on the bottom side
- UART: 6 sets. UART1-6 with dedicated purposes
- Firmware Target Name: SPEEDYBEEF405MINI
- Buzzer: BZ+ and BZ- pad used for 5V Buzzer
- 5V Output: 4 groups. The total current load is 2A
- 9V Output: 1 group. The total current load is 3A
- DJI Air Unit Connection Way: Direct soldering
- Dimension: 30(L) x 32(W) x 7.8(H)mm
- Smart Port / F.Port: Not Supported
- ESC Telemetry: UART R5 (UART5)
- Blackbox: 8MB Onboard Flash
- RSSI Input: Not Supported
- OSD Chip: AT7456E chip
- IMU(Gyro): ICM42688P
- USB Port Type: Type-C.
- WIFI: Not supported
- Barometer: Built-in
- MCU: STM32F405
- Weight: 9.6g
SPEEDYBEE 35A BLHELI_s MINI V2 4-IN-1 ESC
- Mounting: 20 x 20mm ∅3.5mm hole size, compatible with M2 and M3 screws/Silicone grommets
- Power Output: VBAT (Battery voltage, used to power the flight controller)
- Current Sensor: Support (Scale=250 Offset=-500)
- ESC Telemetry: Not supported
- Burst Current: 45A (5 seconds)
- Dimension: 35 * 35 * 5.5mm
- ESC Protocol: DSHOT300/600
- Continuous Current: 35A * 4
- Firmware: BLHeli_S J-H-40
- Power Input: 3-6S LiPo
- Weight: 7.2g
Includes
- 1x SpeedyBee F405 V3 20x20 Flight Controller
- 1x SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC
- 5x M2 Silicone O-Ring
- 5x M5 Silicone O-Ring
- 5x M2 Anti Vibration Silicone Grommets
- 5x M3 Anti Vibration Silicone Grommets
- 1x 8-Pin JST cable 30mm
- 1x 35V 470uf Capacitor
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy