Pay in installments of $17.74 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Aug 6 - Aug 11
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
3.6 Amp Dual USB Charger and 15 Amp Receptacle, White (6-Pack)Charge your USB devices without the need for bulky AC adapters. Enjoy the convenience of 2 standard tamper resistant AC power outlets, with 2 integrated USB charging ports providing 3. 6 Amp of combined charging power. Compatible with popular USB powered tablets, smartphones and E reader devices. Devices provide two 5 Volt DC powered USB ports with a total of 3. 0 Amp 3. 6 Amp charging current Charge most compatible electrical device directly without
Charge your USB devices without the need for bulky AC adapters. Enjoy the convenience of 2 standard tamper resistant AC power outlets, with 2 integrated USB charging ports providing 3.6 Amp of combined charging power. Compatible with popular USB powered tablets, smartphones and E-reader devices.- Devices provide two 5-Volt DC powered USB ports with a total of 3.0 Amp/3.6 Amp charging current
- Charge most compatible electrical device directly without an adapter
- Devices combined power requirements exceed the power capacity of the USB ports, the charger will shut down to protect your electrical devices
- Replace a standard single or duplex receptacle
- Compatible with USB 2.0/3.0 devices, the USB ports are used to charge portable electronic devices only (no data transfer capability)
- Back and side wire for easy installation
- UL/CUL Listed, fully comply with all latest UL 498 and UL 1310 requirements
- Wall plate not included
Features
| Item Weight | 1.71 |
| NEMA Configuration | NEMA 5 |
| Grounding | Isolated Ground |
| Maximum Amperage (amps) | 15 |
| Color/Finish | White |
| Commercial/Residential | Residential |
| Returnable | 180-Day |
| Mounting Type | In-Wall |
| Rating | Tamper Resistant |
| Electrical Features | USB Port |
| Outlet Material | PVC |
| Outlet Configuration | Duplex |
| Number of Poles | 2 |
| Outlet Type | Standard |
| Voltage | 125 volt |
| Package Quantity | 6 |
| Indoor/Outdoor | Indoor |
| Wired or Wireless | Wired |
| Color Family | White |
| Outlet Location | Floor,Wall |
| Number of Outlets | 2 |
| Electrical Product Type | Outlet |
| Outlet Width (in.) | 1.69 |
| Outlet Height (in.) | 4.17 |
| Outlet Depth (in.) | 1.65 |
| Manufacturer Warranty | 2 Year Limited Warranty |
| Certifications and Listings | UL Listed |
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.5 ★★★★★
Based on 26 reviews
Sort
Product Reviews
★★★★★ 5
Easy to use
Works great
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 9, 2026
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024
recommand products
MetroMax 4 36"W x 18"D x 74"H All-Polymer 4-Shelf Starter Shelving Unit
178.50
Cylinder Head Gasket Subaru EJ20 .045" MLS , 103mm Bore Cometic C4360-045
61.13
Jompers Men's Maroon Self Design Kurta Only
22.24
Metro Super Erecta Brite Stationary Wire Shelving Starter Unit, 30-inch W x 18-inch D x 63-inch H, 4 Shelves
132.00
Cylinder Head Gasket Peugeot TU5 J4 .092" MLS , 79mm Bore Cometic C4493-092
173.41