Sirona Spa Care Bromine Start Up Kit

Sirona Spa Care Brom Tabs:

0.015 to 0.1 lb per 300 gallons of water.

Sirona Spa Care Sodium Bromide

Add one-half (1/2) ounce of Sirona Spa Care Sodium Bromide for every 100 gallons of of spa water to establish a 20 parts per million (ppm)

Sirona Spa Care Activate Granular

For Use as a Shock Oxidizer: Apply 2 ounces (4 tablespoons) of this product for every 250 gallons of water.

When used as part of the Sirona Spa Care Bromide Salt Solution and Sirona Spa Care Activate System: Apply 4 ounces (8 tablespoons) of this product for every 250 gallons of water.

Sirona Spa Care Foam Out

Do not use more than one-half (1/2) teaspoon of this product at a time.

Sirona Spa Care Brom Tabs:

Using a suitable feeder adjusted according to the manufacturers directions, add this product to maintain an active bromine concentration of 2 to 4 ppm in residential spas and 3 - 6 ppm in commercial spas. Use a reliable test kit to monitor bromine regularly. This products usage will typically vary from 0.015 to 0.10 pound for every 300 gallons of spa water to maintain the recommended bromine concentration range. The presence of organic debris, high bather use and other factors may require a higher dosage.

Sirona Spa Care Sodium Bromide

This product should be used during the start up process of the Sirona Spa Care program.

1. Circulate the water while adding one-half (1/2) ounce of Sirona Spa Care Sodium Bromide for every 100 gallons of of spa water to establish a 20 parts per million (ppm) bromide reserve.
2. Add Sirona Brom Tabs to establish a proper bromine level.

Note: This is not a sanitizer or a disinfectant. It is used to establish a reserve of bromide in spa or hot tub water. It is also necessary to use a sanitizer to sanitize Sirona

Sirona Spa Care Activate Granular

For Use as a Shock Oxidizer:

1. Turn the filtration system on.
2. Apply 2 ounces (4 tablespoons) of this product for every 250 gallons of water.
3. Circulate water for 15 minutes with the cover off.

When used as part of the Sirona Spa Care Bromide Salt Solution and Sirona Spa Care Activate System:

This product should be added when the spa or hot tub is initially filled and then daily as a shock oxidizer and activator for the production of available bromine in water. The Sirona Activate Granular is not a disinfectant, and will still require chlorine, bromine or other sanitizers to properly sanitize the water.

1. Treat the water with Sirona Spa Care Prevent stain and scale treatment and Sirona Spa Care Enhance Bromide Salt Solution according to the label directions.
2. Apply 4 ounces of (8 tablespoons) of this product for every 250 gallons of water to shock oxidize the spa or hot tub and to release available bromine.
3. Test the bromine residual with a bromine/pH test kit after this product has been added and allowed to circulate for for 15 minutes. The residual must be maintained between 1-3 ppm.

For Maintenance of pH, Bromine Residual and Water Quality:

1. Test the pH of the water daily with a bromine/pH test kit daily and maintain the pH level between 7.2-7.8 because the pH of this product is buffered in this range and will not adversely affect the pH of the water. Do not allow the pH to fall below 7.2.
2. Test the bromine residual daily with a bromine/pH test kit. The bromine residual must be between 1-3 ppm. Heavy usage or the length of time the spa or hot tub is in use may result in depletion of bromine and require additional dosages of this product and/or Sirona Spa Care Enhance Bromide Salt Solution to maintain the desired bromine residual. Never mix any chemicals with each other before adding to the spa or hot tub water.
3. Change the water monthly or as needed to maintain water quality.

Sirona Spa Care Foam Out

1. To prevent foaming, apply a small amount of Sirona Spa Care Foam Out defoamer directly onto the surface of the water. Do not use more than one-half (1/2) teaspoon of this product at a time. Repeat if foaming begins to occur.
2. To eliminate existing foam, apply a small amount of Sirona Spa Foam Out defoamer directly onto the surface of the foam. Do not use more than one-half (1/2) teaspoon of this product at a time. Apply the product when the spa/hot tub is in operation and then wait ten minutes. If foam has not subsided, repeat treatment.