Pay in installments of $181.12 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Aug 6 - Aug 11
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Studio 60 in. Acrylic Corner Drop-in Whirlpool Bathtub in WhiteMaximize your bathing comfort with options for soaking or sitting. The Studio 5959 corner tub, with its luxurious five sided deck surrounding the elongated bathing well and built in molded seat, will make the most of every space in any bathroom. Dramatic in its design and featuring a symmetrical basin that holds 65 gal. of water, the Studio 5959 upgrades your bathing experience to the highest level of luxury. California residents see Prop 65 WARNINGS
Maximize your bathing comfort with options for soaking or sitting. The Studio 5959 corner tub, with its luxurious five-sided deck surrounding the elongated bathing well and built-in molded seat, will make the most of every space in any bathroom. Dramatic in its design and featuring a symmetrical basin that holds 65 gal. of water, the Studio 5959 upgrades your bathing experience to the highest level of luxury.- California residents
- Acrylic with fiberglass reinforcement for added durability
- Corner single person tub with built-in seat
- 6 fully directional adjustable PVC jets
- 2.25 HP single speed pump
- Air switch on/off control
- Soft touch electronic on/off control with 30 minute timer
- Standard HydrOzone sanitation system
Features
| Item Weight | 145 |
| Style | Straight |
| Water capacity (gallons) | 65 |
| Exterior bath shape | Neo Angle |
| Number of Jets | 6 |
| Color/Finish | White |
| Voltage (volts) | 110 |
| Product Weight (lb.) | 145 |
| Returnable | 180-Day |
| Tub/Shower Features | Adjustable Jet Direction,Adjustable Jet Flow,Slip-Resistant Tub |
| Material | Acrylic |
| Style2 | Minimalist,Modern |
| Drain Location | Center |
| Number of jet settings | 1 |
| Maximum Number of Occupants | 2 Person |
| Included | No additional components or accessories are included |
| Bath Therapy Type | Whirlpool |
| Faucet mount | Variable |
| Control Type | Manual |
| Wattage (watts) | 1552.5 |
| Color Family | White |
| Maximum Number of Occupants2 | 2 |
| Basin Length (in.) | 51 |
| Overall Width (in.) | 56 |
| Soaking Depth (in.) | 18.25 |
| Overall Height (in.) | 19 |
| Basin Width (in.) | 56 |
| Overall Length (in.) | 59 |
| Manufacturer Warranty | 5 Year Limited Warranty |
| Certifications and Listings | IAPMO Certified,UL Certified |
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.6 ★★★★★
Based on 7 reviews
Sort
Product Reviews
★★★★★ 5
Easy to use
Works great
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 9, 2026
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024
recommand products
Cylinder Head Gasket Subaru EJ20 .045" MLS , 103mm Bore Cometic C4360-045
61.13
Cylinder Head Gasket Nissan 1994-2002 SR20DE/SR20DET .098" MLS , 88.5mm Bore, RWD, With VCT Cometic C4283-098
157.72
Metro Super Erecta 72 x 21 x 74 Add-On Wire Shelving Unit, 5 Shelves, Metroseal 3 Green Epoxy with Microban
325.50
Jompers Women's Pink Ethnic Motifs Ikat Kurta with lace work
24.42
Cylinder Head Gasket Peugeot TU5 J4 .092" MLS , 79mm Bore Cometic C4493-092
173.41